The Ultimate Vaping Experience with V Max Variable Voltage Personal Vaping Machine by SmokTech

May be purchased as VMax Body Only

Or

VMax Deluxe Kit

1 VMaxx 5Amp VV 3V~6V Body Tube

2 IMR 18350 800mAh Batteries

1 5 Pack of 4.5ohm Smoktech Cartomizers

1 Trustfire Dual Battery charger and cable

The Original and the Best of the Variable Voltage Smoktech Max Family

• PCB with 5 Amperage output limit
• Voltage Range: 3.0--6.0 V with 0.1 incrementsvolt
• Smok VV accuracy: +/- 0.1 V
• Large 3 Digit Digital Display
• Selectable Display info: atomizer resistance, battery under-load voltage, Output voltage
• Translucent 360° turnning light-up button with low battery warning
• 510 connection
• 4 + 1 VENT-HOLE Bottom Cap
• Work on 2 pcs IMR 18350
• Short Circuit protection
• Reverse battery protection
• Battery Monitoring
• Over-Discharge Protection
• On/Off Mode

Instructions for use can be found below

 Built-in three digit LED display allows you to visually adjust your voltage

 VMax PCB allows 5 Amperage output limit

Atomizer Ohm Check

UU- Power up
UD- Power down
SO- Power on/off
UC- Battery Check
DS - display information setting
*do- atomizer output voltage
*du- battery output voltage
*dR - atomizer ohm
LO- LED on/off

To Adjust VMax Power Up:

1. Press the button 3 times in a row until "UU" is shown on the display.
2. When UU is shown on the display, leave the button idle for 2 seconds. The display will change to show the last voltage selected.
3. Once the voltage is displayed, each time you press the button the voltage will advance to the next higher setting: 3.1,3.2,3.3 etc. When you reach 6.0, it will rotate back to 3.0 and go up again.
4. When you have reached the desired setting, leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.

To Adjust VMax Power Down:
1. Press the button 4 times in a row until "UD" is shown on the display .
2. When UD is shown on the display , leave the button idle for 2 seconds. The display will change to show the last voltage selected.
4. Once the voltage is displayed, each time you press the button the voltage will advance to the next lower setting: 5.9,5.8,5.7 etc. When you reach 3.0, it will rotate back to 6.0 and go up again.
4. when you have reached the desired setting, leave the button idle for 2 second. The setting will be saved and VV will resume normal operation.

VMax ON/OFF Power:
1. Press the button 5 times in a row until "SO" is shown on the display.
2. When UD is shown on the display, leave the button idle for 2 seconds. The display will show the last setting, on or off .
4. Each time you press the button the display will toggle between on/off.
4. When you have reached the desired setting, leave the button idle for 2 seconds. If you selected "OF" the VV will go into standby mode.

Check Your Vmax Battery Voltage:
1. Press the button 6 times in a row until UC is shown on the display.
2. When UC is shown on the display, leave the button idle for 2 seconds, the digital display will show your battery voltage measurement.
3. The battery voltage will be displayed for 2 seconds, then the display will turn off.

To Display Vmax Settings During Vaping:
1. Press the button 7 times in a row until DS is shown on the display,
2. When DS is shown on the display, leave the button for 2 seconds, the display will show the current setting: DO, DU or DR.
3. Each time you press the button, the setting will toggle among "DO" "DU" or "DR" ,
4. When "DO" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer working output voltage during your vaping;
5. When "DU" is chosen, leave the button idle for 2 second, the setting will be saved and the display will show your battery voltage during your vaping.
6. When "DR" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer resistance during your vaping.

ON/OFF of LED
1. Press the button 8 times in a row until "LO" is shown on the display.
2. When LO is shown on the display, leave the button idle for 2 seconds, the display will show the current setting: ON/OFF .
3. Each time you press the button, the setting will toggle between on/off.
4. When you have reached the desired setting, leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.

Short Circuit Protection:
The display will show the following error code when there is a short circuit:
1. F1: resistance for the heating coil of cartomizer is bigger than 0.5R, or smaller than 1.3R
2. F2: resistance for the heating coil of cartomizer is smaller than 0.5R

VMax Variable Voltage PV By Smoktech