Loading... Please wait...

Our Newsletter


Snow Wolf 200W Dual 18650 Box Mod

Price:
$99.99
Quantity:


Product Description

Snow Wolf 200 Watt Dual 18659 Battery Box Mod by Asmodus

200 Watt Temperature Control

White Snow Wolf or Black Snow Wolf  *** Now Available

Latest and improved version

200W Snow Wolf Features

  • Adjustable temperature control
  • Low voltage protection
  • Low resistance protection
  • High input voltage warning
  • Output short circuit protection
  • Reverse battery protection
  • Overheating prevention

Snow Wolf Specs

  • Accommodates 2 18650 sized batteries
  • Variable wattage range: 5.0 - 200 watts
  • Output voltage range: 0.5 - 7.0 volts
  • Atomizer resistance range: 0.05 - 2.5 ohm
  • Battery voltage range: 6.2 - 8.4 volts
  • Temperature control range: 100 - 350°C / 212 - 662°F
  • Supports both Kanthal and nickel wires

INSTALLING THE BATTERIES INTO YOUR SNOW WOLF BOX MOD
Please install batteries before use. To ensure correct installation, follow these instructions: Open the battery panel; insert batteries into battery slots with the positive and negative poles aligned as illustrated; ensure ribbon is wrapped around batteries to remove the batteries easily. To remove the batteries, pull on the loose end of the ribbon to lift batteries out of their slot.

TURNING THE SNOW WOLF DEVICE ON
Once batteries are installed, the device enters “turn-on mode” with the logo displayed, and will then enter into “lock mode” shortly after. Press the fire button 5 times consecutively within 3 seconds to unlock the device. After unlocking the device, atomizer resistance, output wattage, output voltage, battery level, and current regulated temperature will be displayed. Without an atomizer installed, the output voltage will read 0.00V and resistance will read 0.00Ω. If you attempt to fire without an atomizer installed, “CHECK ATOMIZER” will be displayed.

UNLOCKING THE SNOW WOLF DEVICE
When the device is locked, pressing any button will show the message “LOCKED CLICK 5X”. When “LOCKED CLICK 5X” is displayed, press the fire button 5 times consecutively within 3 seconds to unlock the device. Your device is now ready to vape.

ADJUSTING THE SNOW WOLF WATTAGE SETTINGS
If you would like to adjust the wattage, press both the “+” and “-” buttons simultaneously until the “W” in front of the wattage value is flashing. Now by pressing the “+” or “-” buttons you can increase or decrease the wattage respectively. The output wattage range is 5.0 to 200.0W. By pressing “+” below 50W, watts increase by 0.1 increment; above 50W, watts increase by 0.5 increments; above 100W, watts increase by 1 increment. By pressing “-”, below 50W, watts decrease by 0.1 increment; above 50W, watts decrease by 0.5 increments; above 100W, watts decrease by 1 increment. When wattage is higher than 150W, the system is pulse output and the upper right corner of the screen will display a "P" symbol.

ADJUSTING THE SNOW WOLF TEMPERATURE CONTROL
NOTE: Only when using pure nickel wires in your atomizer build will the temperature control function work. Ordinary wires can only make use of the watt adjustment function.
If you would like to adjust the temperature, press both the “+” and “-” buttons simultaneously until the “°C” or “°F” in front of the temperature value is flashing. Now by pressing the “+” or “-” buttons you can increase or decrease the temperature respectively. The temperature range is 100-350°C / 212-662°F. By pressing the “+” or “-”, temperature will increase or decrease by 1°C / 1°F. The system can switch between °C and °F by scrolling pass the minimum or maximum temperatures. (i.e. when you click “+” upwards to 662°F and continue to hold the button, it will automatically switch to 350°C; when you click “-“ downwards to 212°F and continue to hold the button, it will automatically switch to 100°C, and vice versa.)

TURNING THE SNOW WOLF DEVICE OFF
When device is not in use, the screen will darken after 20 seconds. After 30 seconds the display will turn off and the device will enter standby mode. After 30 minutes in standby mode, device will automatically lock. Press the fire button 5 times in 3 seconds consecutively anytime during standby mode to turn off the device. “SYSTEM OFF” will then read on the display. Press any button to wake up the system.

BATTERY INFORMATION FROM YOUR SNOW WOLF 200W MOD
When battery voltage is lower than 6.2V, device will display “LOW BATTERY”. When battery power is low and does not match the current wattage or temperature setting, device will display ”CHECK BATTERY” and stop firing. When battery voltage is less than 5.4V, device will not power on; when this display appears, change batteries before use.

RESISTANCE RANGE OF YOUR SNOW WOLF MOD
This SNOW WOLF device supports only a resistance range from 0.05Ω - 2.5Ω, otherwise the device will not fire. When the resistance is lower than 0.05Ω, “LOW ATOMIZER” will be displayed and will not fire; when the resistance is higher than 2.5Ω, “HIGH ATOMIZER” will be displayed; when there is no atomizer, “CHECK ATOMIZER” will be displayed; when the atomizer shorts, “ATOMIZER SHORT” will be displayed.

ATOMIZER INSTALLATION AND DISASSEMBLE ON YOUR SNOW WOLF
If you remove the atomizer while the device is on and press the power button, “CHECK ATOMIZER” will be displayed. If you remove the atomizer while firing, “ATOMIZER REMOVE” will be displayed. When the device is on and you install an atomizer, “NEW COIL UP SAME DOWN” will be displayed; press the ‘–‘ button if it is the original atomizer, press the ’+’ button if a new atomizer has been installed.


NOTE: Please make sure the new atomizer is cold, otherwise the device will misread the atomizer resistance

Find Similar Products by Category

Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!

Add to Wish List

Click the button below to add the Snow Wolf 200W Dual 18650 Box Mod to your wish list.

You Recently Viewed...